61S14XAB Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- june from wills point, TX
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glynne from Dedham, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Oven was not working at all
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wesley from ODENVILLE, AL
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
original fixture required bulb - this fixture (all-in-one) was great
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNIE from SAG HARBOR, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Igniter for oven not working
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from West Winfield, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light reliably.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Cocoa, FL
- Parts Used:
- 12001596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burners would not lite
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped. Thanks Lloyd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELMER from BONNEY LAKE, WA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter was not getting hot enough to allow burner to come on.
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eric from winter haven, FL
- Parts Used:
- 12001596
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
no spark on top burners
part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from ELKTON, VA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gino from ARLETA, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
igniter failed to ignite
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Israel from HYATTSVILLE, MD
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The igniter of the burner was worn out of constant use.
First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from SAN DIEGO, CA
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Replaced upper over light and assembly
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from ALBANY, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Was this instruction helpful to you?
Thank you for voting!