C3523WVV Magic Chef Range - Instructions

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job

Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.

Removed screws of old element pulled clips off replaced with new element very easy

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

just plugged it in!

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.

Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).

I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concise diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks