CGR1330BDC Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ovide N from Abbeville, LA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
oven door gasket torn
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Washburn, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven wouldn't heat causing the house to smell of gas
took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doreen from DOUGLAS, WY
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Oven igniter went out of my oven.
Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Braintree, MA
- Parts Used:
- WP74002352
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old thermostat broke
The installation was very easy.
The knob fit right into place and that was it.
No screws or tools were necessary.
There was a "D Shaped" slot in the back of the knob that slid right into the metal piece attached to the stove.
The delivery was very quick and the ordering process was very easy.
The knob fit right into place and that was it.
No screws or tools were necessary.
There was a "D Shaped" slot in the back of the knob that slid right into the metal piece attached to the stove.
The delivery was very quick and the ordering process was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Monroe, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
floor panel heavily stained and warped
slide latches in rear of floor panel forward and remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from WINCHESTER, MA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from BUDA, TX
- Parts Used:
- 74007498
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
My igniter burnt out. My oven stopped lighting up.
I ordered a new igniter and when it arrived, i removed the door from the oven. It just lift's off. I had to removed two screws from the bottom plate to gain access to the igniter. Remove the two screws from the igniter and unplug it from the back of the lower back of the stove. Place the new igniter where the old one was and plug it in. Put new screws in and tighten them down. Put the bottom plate back in its place with screws tightened. Put oven door back on and turn on the oven. That's all there is to it. Your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from delavan, WI
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven does not heat but broiler works
Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mona from BROOKLYN, NY
- Parts Used:
- WP74002352
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The face of Temperature marking position is different from my old knob
I cannot use the thermostat knob on my “Magic Chef - With Uniburners” stove because the temperature markings are off.
The “WARM” on the new knob is “OFF” on my old knob!
What should I do to make the new knob works with my stove? Please advise.
Thank you..
The “WARM” on the new knob is “OFF” on my old knob!
What should I do to make the new knob works with my stove? Please advise.
Thank you..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from LYNDEN, WA
- Parts Used:
- 74007498
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No problem
Very easy install. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Reno, NV
- Parts Used:
- 74003387
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old bulb fused into old socket.
removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allison from MAYNARD, MA
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would preheat but would not maintain temperature or sometimes would not preheat. Was temperamental
1. Remove the oven door by opening a few inches and lifting straight up. Remove racks to access it. 2. The old igniter is just held in by two nuts that have a screw head in the middle of them so they could be removed by a nut driver or by a screwdriver. Unfortunately, both of our screws threads were terribly stripped and after first trying to use pliers to help remove them, we ended up using a dremel tool to cut them off. 3. unplug the old igniter and take it out. 4. Plug in the new igniter. 5. attach the two screws. (our time on the repair was mostly spent trying to find two screws around our house that would replace the two that were stripped--otherwise this would have been 15 minutes). 6. return the door and racks by the sliding the door downwards onto the hinges
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billye from San Antonio, TX
- Parts Used:
- 1430283
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Range burner drip pans were rusted and old
The repair was super simple, just remove the drip pan and place new one.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the future for needed parts.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the future for needed parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!