Models > 3468XTW-X > Instructions

3468XTW-X Magic Chef Range - Instructions

Jump to:

All Instructions for the 3468XTW-X
106 - 120 of 377
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert from Clymer, NY
Parts Used:
12400035
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven would not turn on
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Westcliffe, CO
Parts Used:
12001655
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Oven did not heat up in bake mode.
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rhoda P. from Secaucus, NJ
Parts Used:
WP3413F018-19, WP3401F075-19
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
june from wills point, TX
Parts Used:
12400035
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Glynne from Dedham, MA
Parts Used:
12400035
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Oven was not working at all
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pati from Marietta, GA
Parts Used:
WP74006427
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
Oven wouldn't heat, broiler would.
Removed all screws from back panel of stove, disconnected all electrical, shut off gas. Removed valve and replaced with new. Put all back together. Turned on gas and checked for leaks. Success!!
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from West Winfield, NY
Parts Used:
12400035
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
oven would not light reliably.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RONNIE from SAG HARBOR, NY
Parts Used:
12400035
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set
Igniter for oven not working
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ben from Belen, NM
Parts Used:
12001655
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven shutting off, getting an F1 error on ECM
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ELMER from BONNEY LAKE, WA
Parts Used:
12400035
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Igniter was not getting hot enough to allow burner to come on.
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
wesley from ODENVILLE, AL
Parts Used:
WP7407P182-60
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
original fixture required bulb - this fixture (all-in-one) was great
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lloyd from Cocoa, FL
Parts Used:
12001596
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Burners would not lite
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dominick from CLARKS SUMMIT, PA
Parts Used:
12400035
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set
Oven would not ignite
Very easy, video helped tremendously
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gino from ARLETA, CA
Parts Used:
12400035
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
igniter failed to ignite
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeri from NEW RICHMOND, OH
Parts Used:
74002312
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
One of the broiler drawer guides broke
All I had to do was pull the drawer out and screw on the new part! Awesome experience...and it was so easy to find the part on the website, everything is very clear and with pictures to ensure where the part belongs...who could ask for more?
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 3468XTW-X
106 - 120 of 377