3862XVW Magic Chef Range - Instructions

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making my problem, no problem at all!

I took the broiler pan out of the shipping container and put it in the oven.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!

Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!

Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Pulled the drawer and removed the oven door by pulling it upward. Then removed the two hex head screws which loosened the old hinge and pulled it down out of the side of the oven box. Replaced the new hinge in the position of the old one and installed the two hex head screws. I replaced the oven door and that was when I realized the part was wrong. The parts description in the view on the website was one number off and I replaced the broken hinge and ordered from another site the right number. That hinge works.

Unplug the 220 cord..remove rear metal back ( 7-8 Ph/screws)... disconnect the red & yellow connectors from the back of the lower element. Remove-the-lift-off Oven door. Remove the two Ph/screws (one on either end of the element) At the very rear of the oven. Install the new element and reverse the about to reassemble.