CER1115AAW Magic Chef Range - Instructions

When ordering the replacement part, read the posts on how to replace the bake element. Just follwed their lead. The only difficulty is getting a hold of the wire at the back of the range that the bake element plugs into. There wasen't much play in the wire.
PS Be sure and remove the range door or have very long arms.

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

just plugged it in!

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

I unplugged the cord to the stove. Then I removed the two screws on the broken heating element. Once the screws were removed, I slid off the two wires attached to the element prones. Grab the new element and attached the two wires. Reinstalled screws. Plugged in the cord, and turned on oven. Heating element came on.

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

Turned the power off to the oven, unscrewed the ends of the element, connected new element, screwed it back in to place and turned the powe back on. The video provided in my shipping confirmation was very helpful.

It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.

Turned oven circuit breaker off. Removed oven racks. Removed 2 screws from old element. Pulled element out slightly disconnected wires on each end and reattached to new element. Pushed back in and reinstalled the 2 screws, reinstalled oven racks and turned circuit breaker back on. All done in about 20 minutes.

super easy after watching the how to video you had on it and iam the wife not the husband it was so easy thanks

I reoved old drip pans and installed new ones. Very easy, they look great!

Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .

I had the part overnighted since Thanksgiving was in two days and we needed to be able to use the oven. I saw a video on the website that instructed how to unplug the stove. Unscrew the baking element from the inside of back wall of oven. Gently pull out the part to where it is attached to wires. Simply pull apart the male part from female parts. Replace the old element with new element and attach it to the pulled out wires. Then gently push back wires inside the back wall of oven. Screw the attachment back in. We then plugged the oven back in. Turned on the oven to about 300 degrees. We put an oven temperature gauge inside and after a time the oven temperature was at 300 degrees and steady. It was fixed. Thanksgiving was on!

the hardest part of this repair was the wait for the element to arrive in the mail - which was in 4 business days - then took 5 to 10 minutes to get to circuit breaker box in garage. That was the longest part of the repair. My husband took the door off the oven after turning the circuit off in the garage. Followed directions from others who made the same repair and it was done in 2 minutes! Super easy - thanks for saving us money during this time of tight budgeting around the holidays! You're a lifesaver!

First I turned the power off to the oven using the breaker switch. Removed the old bake element by first unscrewing the 2 screws for each bracket holding each side of the old bake element and unplugging the two current connections.

Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.