B38HA-2CXW-ON Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Suzanne from COZAD, NE
- Parts Used:
- WPW10259868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The three braces under the coils had weakened and fallen apart
I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CONCORD, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Burner plugs were loose
used the supplied parts...very easy. The parts were exact replacements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from Harrodsburg, KY
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Receptacle had become bad poor connection.
First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Traverse city, MI
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
element shorted out startedto arch inside oven
Turned off power, first then removed two screws
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shawn from Vancouver, WA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The burner was shortening out and would work sometime. The first time I replace the burner but the new one shorted out quickly.
I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from Hampton, VA
- Parts Used:
- WP7711P466-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing clock knob
placed knob on clock shaft with my fingers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from Charleston, SC
- Parts Used:
- WPW10259865
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface burner heating element broken
took out old element, replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Camp Springs, MD
- Parts Used:
- 7201P003-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Had to replace heating element and element gasket
Removed old element and element gasket. Replaced both by alining gasket with element and screwing in retaining screws. Jod completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Atlanta, GA
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Manchester, MD
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Sockets for the burner elementss were burned out
I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aurelio from Lebanon, NJ
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Bad broil grill
Once oven was removed from wall not to bad
Was this instruction helpful to you?
Thank you for voting!