3841SVA-D Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- wayne from LIMINGTON, ME
- Parts Used:
- WP9781049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
oven light glass cover was broken
took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Foxboro, MA
- Parts Used:
- WP74003019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake Element wouldn't heat up to temperature
I had viewed the video link on PartsSelect. I removed 2 screws and proceeded to pull element out to disconnect wire connectors. However one side the wire connected was melted on to the contact tab of the element and the wire was broken off. I proceeded to remove back panel from stove and located the exposed broken wire. I stripped back wire and installed a new wire connector that I had in my tool box. I fed wire through small hole. Then I re-installed back panel. I then connected wires to the new bake element and installed element mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from FREMONT, CA
- Parts Used:
- WPW10196406, WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Used part
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marylou from Sitka, AL
- Parts Used:
- WPY04000036, WPW10196405, W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace stove pans and burner
An easy replacement job.
Service from you was prompt and the replacement parts arrived in perfect condition...thanks
Service from you was prompt and the replacement parts arrived in perfect condition...thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard C from San Jose, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Frayed and exposed receptical wires in cartridge
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from SAN DIEGO, CA
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Replaced upper over light and assembly
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light assembly from the front of the oven and had to go in from the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from SOUTHBURY, CT
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Jennair cooktop with coils lost one of its coil guides.
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Fredericksburg, VA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven baking coil had burned out
Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Littleton, CO
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The bake element burst.
Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn S from white oak, NC
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom bake element broken and burned
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Schertz, TX
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element would no longer heat up
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Neenah, WI
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven heating element burned out like a lit fuse!
Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Marietta, GA
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out.
Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hudson from Cockeysville, MD
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element was completely gone.
Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TONI from SALISBURY, NC
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element had cracked
First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.
Was this instruction helpful to you?
Thank you for voting!