CER1360AGW Magic Chef Range - Instructions

Turned oven circuit breaker off. Removed oven racks. Removed 2 screws from old element. Pulled element out slightly disconnected wires on each end and reattached to new element. Pushed back in and reinstalled the 2 screws, reinstalled oven racks and turned circuit breaker back on. All done in about 20 minutes.

super easy after watching the how to video you had on it and iam the wife not the husband it was so easy thanks

I reoved old drip pans and installed new ones. Very easy, they look great!

First I turned the power off to the oven using the breaker switch. Removed the old bake element by first unscrewing the 2 screws for each bracket holding each side of the old bake element and unplugging the two current connections.

Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.

Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .

I had the part overnighted since Thanksgiving was in two days and we needed to be able to use the oven. I saw a video on the website that instructed how to unplug the stove. Unscrew the baking element from the inside of back wall of oven. Gently pull out the part to where it is attached to wires. Simply pull apart the male part from female parts. Replace the old element with new element and attach it to the pulled out wires. Then gently push back wires inside the back wall of oven. Screw the attachment back in. We then plugged the oven back in. Turned on the oven to about 300 degrees. We put an oven temperature gauge inside and after a time the oven temperature was at 300 degrees and steady. It was fixed. Thanksgiving was on!

the hardest part of this repair was the wait for the element to arrive in the mail - which was in 4 business days - then took 5 to 10 minutes to get to circuit breaker box in garage. That was the longest part of the repair. My husband took the door off the oven after turning the circuit off in the garage. Followed directions from others who made the same repair and it was done in 2 minutes! Super easy - thanks for saving us money during this time of tight budgeting around the holidays! You're a lifesaver!

I took the broiler pan out of the shipping container and put it in the oven.

after finding my part and thank god for you guys i recieved it early it only took 4 days to get here i unscrewed my old oven part and popped the new one in easier than making cookies and now i can bake til my hearts content thanks for being there for me
barbara krebs

An easy replacement job.

Service from you was prompt and the replacement parts arrived in perfect condition...thanks

-Disconnected power from oven at the circuit breaker.
-Removed oven door and racks.
-Removed two screws holding element to the rear wall.
-Carefully pulled element away from rear wall, exposing wire leads.
-Carefully detached wire leads with male Sta-Kon connectors from element ends. (Taking care not to break or weaken the wires at the connector.)
-Disposed of old element and placed new element in same position.
-Re-attached leads by very carefully sliding male Sta-Kon connectors into the new element connectors, taking care not to push too hard and bend element wire.
-Gently re-inserted element ends into wall and re-attached element to wall with original screws.
-Reconnected power and tested new element. Element did not heat.
-Disconnected power and looked for collateral damage from original element failure.
-Removed oven from wall, removed rear panel and identified the high-temperature limit switch.
-Removed Sta-Kon leads and checked switch for electrical continuity. It had none, apparently the result of the high current from original element short.
-Obtained new hi-limit switch from Part Select
-Removed and replaced hi-limit switch, re-attached leads.
-Replaced rear panel and reinserted oven in wall.
-Reconnected power and tested new element. Element heated normally.
-Returned racks to oven, re-attached door and done.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.