CER3725AGW Magic Chef Range - Instructions

-Disconnected power from oven at the circuit breaker.
-Removed oven door and racks.
-Removed two screws holding element to the rear wall.
-Carefully pulled element away from rear wall, exposing wire leads.
-Carefully detached wire leads with male Sta-Kon connectors from element ends. (Taking care not to break or weaken the wires at the connector.)
-Disposed of old element and placed new element in same position.
-Re-attached leads by very carefully sliding male Sta-Kon connectors into the new element connectors, taking care not to push too hard and bend element wire.
-Gently re-inserted element ends into wall and re-attached element to wall with original screws.
-Reconnected power and tested new element. Element did not heat.
-Disconnected power and looked for collateral damage from original element failure.
-Removed oven from wall, removed rear panel and identified the high-temperature limit switch.
-Removed Sta-Kon leads and checked switch for electrical continuity. It had none, apparently the result of the high current from original element short.
-Obtained new hi-limit switch from Part Select
-Removed and replaced hi-limit switch, re-attached leads.
-Replaced rear panel and reinserted oven in wall.
-Reconnected power and tested new element. Element heated normally.
-Returned racks to oven, re-attached door and done.

First I turned the power off to the oven using the breaker switch. Removed the old bake element by first unscrewing the 2 screws for each bracket holding each side of the old bake element and unplugging the two current connections.

Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.

I had the part overnighted since Thanksgiving was in two days and we needed to be able to use the oven. I saw a video on the website that instructed how to unplug the stove. Unscrew the baking element from the inside of back wall of oven. Gently pull out the part to where it is attached to wires. Simply pull apart the male part from female parts. Replace the old element with new element and attach it to the pulled out wires. Then gently push back wires inside the back wall of oven. Screw the attachment back in. We then plugged the oven back in. Turned on the oven to about 300 degrees. We put an oven temperature gauge inside and after a time the oven temperature was at 300 degrees and steady. It was fixed. Thanksgiving was on!

the hardest part of this repair was the wait for the element to arrive in the mail - which was in 4 business days - then took 5 to 10 minutes to get to circuit breaker box in garage. That was the longest part of the repair. My husband took the door off the oven after turning the circuit off in the garage. Followed directions from others who made the same repair and it was done in 2 minutes! Super easy - thanks for saving us money during this time of tight budgeting around the holidays! You're a lifesaver!

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

Take out 2 screws. Unplug the old element, plug in the new one and put the screws back in.

My daughter repaired it without any problems.

Just took the old one out and put the new one in. Very easy!

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.

Unscrewed two Phillips screws holding the element in the back of the oven, pulled out the element and the leads, disconnected the wires, removed element from oven and reversed the process to install new one. One most important and critical maneuver - the element is connected to the hot wire on the left side and the switch shuts off the element by disconnecting electrical flow to the neutral side of the power so its not enough to just have the oven turned off - makes one heck of a spark when the wire touches the stove panel when you pull the wire through the hole (220 at 60 amps).

Video showed element being unplugged from inside oven. My oven wires did not extend into oven cavity and they fell behind the back oven wall when I unplugged them. After trying to catch the two wires using needle nose pliers through 3/4" holes several times, I finally decided to take the complete back off the range. When I did this, I was able to see the wires with the female couplings. I then had my wife firmly hold the new element against the back of the oven from inside letting me connect the wires to the new element and replace the oven back. THIS WOULD HAVE QUALIFIED AS "EASY" AND A 15 TO 30 MINUTE JOB if this technique had been known from the outset.

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful