CER3525AAW Magic Chef Range - Instructions

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

Unscrewed two Phillips screws holding the element in the back of the oven, pulled out the element and the leads, disconnected the wires, removed element from oven and reversed the process to install new one. One most important and critical maneuver - the element is connected to the hot wire on the left side and the switch shuts off the element by disconnecting electrical flow to the neutral side of the power so its not enough to just have the oven turned off - makes one heck of a spark when the wire touches the stove panel when you pull the wire through the hole (220 at 60 amps).

replaced element with new one , worked perfectly-

Pulled the drawer and removed the oven door by pulling it upward. Then removed the two hex head screws which loosened the old hinge and pulled it down out of the side of the oven box. Replaced the new hinge in the position of the old one and installed the two hex head screws. I replaced the oven door and that was when I realized the part was wrong. The parts description in the view on the website was one number off and I replaced the broken hinge and ordered from another site the right number. That hinge works.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful

Followed a simple video and completed this repair in just 5 minutes, gasket came out easily and the new one went in easily . Cleaning the oven door was the hardest part.

My daughter repaired it without any problems.

Very helpful customer service Lady.
Helped me select the corect burner replacement.
And helped me get it ordered.
Repair went very well.
I recomend Parts Select if you need parts for.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Take out 2 screws. Unplug the old element, plug in the new one and put the screws back in.

It was easy finding the part on line and the part was delivered within three days. It only took about 10 minutes to change element. I was so pleased with the product, that I just changed a thermostat on my parents stove which was purchased through parts select and that was very easy to change also.

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!