CGR3520ADL Magic Chef Range - Instructions

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

I was not sure what was causing the problem, I thought at first it was low water pressure causing the hollow ice cubes. After some trial and error testing I figured a likely cause could be the water valve in the ice maker itself. I replaced that part rather easily using the existing fasteners in about 15 or 20 minutes. The ice maker has been working flawlessly since the repair.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wrench. Lift the valve out. Reverse the steps to install the new valve.

After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.

Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) Then I put the new valve in, put the cover back on the refridgerator and was done. total time 15 minutes. My wife says I'm the man.

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by removing the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who added their comments! They gave us courage to give it a try.

I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !

First pull out frig and unplug. Shut off water valve. I just had to remove two screws to disconnect unit from bottom rear corner of frig. Pull element out just a few inches and disconnect the plug that feeds it electric. Disconnect water hose and reattach to new unit. Reconnect electric plug and reinstall in back of frig, securing with two screws. I have an older appliance, so I had to jury rig a bit when reattaching new unit by drilling two new holes for mounting. Also, I had to buy a new water hose because the old part would not accept the standard female end of the hose to connect to. Home Depot has the standard icemaker hoses with two female ends. These two glitches would probably not apply to a newer appliance, but anyway, it's cranking out the ice just fine now! Sure I saved alot of money, even with the extra $10 investment for the hose.