3110PRW Magic Chef Range - Instructions

I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....

It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

Saw that the igniter came on, but no gas flow.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.

Pulled the old knob off and put the new one on. Only thing that was difficult was making sure the knob was the right one because the instructions kept leading me back to a different brand of appliance but since the photo looked alike I went ahead and got it.

We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!

Removed the aftermarket knobs I originally bought (they would slip or not turn at all) and installed the new Magic Chef knobs on stove. They work perfect! No problems, easy to install and work every time. Thank you so much for your quick shipment. It is now fun again to be cooking, and not worrying about whether the knobs will turn or not. Thank you, thank you

Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.

Easy......pulled out the old one easily and popped in the new one.......saved a lot of money...no repair bill for either diagnostic fee or assembly fee ...No mark up for the part either. Very happy mom!

I was tired of guessing the temperature on the oven in my apartment so I decided to look on-line to see if I could find a replacement. I couldn't find the exact Model Number to the old stove so I just took the old thermostat knob out and looked for pictures on the PartSelect site that matched up. I found one that was almost an exact match so I decided to take a chance and order it. I was so happy when I received my replacement. It was a perfect fit. All I had to do was take the old knob out and put the new one in. Thanks PartSelect!

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.

Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pushed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.