34FB-4CKXW Magic Chef Range - Instructions

Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..

I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .

Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven worked perfectly

Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, you will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.

it was so easy my wife could do it!!!!!!!!

I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.

placed knob on clock shaft with my fingers

Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.