3127WTV Magic Chef Range - Instructions

Very easy, video helped tremendously

Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.

I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!

First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out back first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!

Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the part and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.

I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.

To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!

It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!

If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.

Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!

replace burner-had to hit old burn with rubber mallet to break off grease and took old burner off-two wires were connected to it..put those on new burner and was done--have a little problem--flame is lower now than it was-but it turns on

took oven tray out and loosened igniter and replace same works great.