31FB-3KLX Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Otto from Bridgeport, CT
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor lights but gas does not come on
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luz M. from North Providence, RI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven didn't get hot
was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from SALEM, OR
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not heat. Broiler was fine, just no oven.
Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from breaux bridge, LA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light
open oven door remove bottom tray pull off two screws unplug wire remove old part install new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- collins from Freeport, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Front Burners
Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HELMUT from MIDDLE VILLAGE, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven would not light even though the glow plug lit.
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Camillus, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
On/off sputter of stove. Ignitor/glow bar problem.
Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rick from chariton, IA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
would not light oven
2 screws easy to remove and plug in the wire. job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Delano, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not ignite
I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Farmington Hills, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not work, broiler and range did work.
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.
Rick,
Detroit, MI.
Rick,
Detroit, MI.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mitch from brooklyn park, MN
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven didnt light
i removed old part, then installed new one. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Mayville, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ignitor would heat enough to open gas vavle to lite oven
unplugged the oven, unplugged the ignitor and removed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Dearborn, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat to temp and could smell gas.
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Greenwood, AR
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not light, but igniter would glow.
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Girdwood, AK
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
very slow heating, smell of gas
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this instruction helpful to you?
Thank you for voting!