CGR1415ADH Magic Chef Range - Instructions

Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.

Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

First I slided the door off it's hinges to make it easy
to get to the two screws holding bottom trim on
remove these screws slide in new glass replaced the trim and installed the two screws.
piece of cake total time 10 -15 min.

First I removed the bottom plate in the oven. The ignitor was located at the rear of the burner and I removed to screws and it was loose except for the two wires. Next I removed the bottom tray from the stove. Two screws held the metal guard in place at the rear of the stove. After removing the plate, I determined which wires belonged to the ignitor, unplugged them at the coupling and pulled the wires out through the bottom of the oven. Replacing the ignitor was simply to reverse the proceedure. PartSelect got the part right out to me, installing the new part was a breeze, and my wife calls me her "hero." This site was a real help and saved me a service/repair bill. Thanks!
Fred

The oven was inconsistanty lighting and I could not predict when it would. After reading some repair reviews I determined that the problem was most likely the igniter. I purchased one from your site and it arrived the next day. Awsome! Had to take out six screws to get to the wiring and removed the igniter. The wiring was a simple plug. Replaced the igniter in about 20 minutes and the oven has been working flawless every since. THANKS!

Remove the oven door by opening halfway and lifting door away from stove. Removed racks and bottom pan from oven area exposing the gas bar and vertical mount igniter. Next remove bottom storage door. With phillips screwdriver remove 2 screws securing rear cover plate in back of storage area, accessing the igniter connection, and unplug the plug. Next back in oven, remove 2 5/16 sheet metal screws securing igniter with a nut driver and remove igniter by getly pulling disconnected end thru to oven. Now reverse process, install new vertical mount igniter and push connection down thru to storage area, then reconnect wire connection and put cover plate back on.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.

I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.

took out burner and remove ignite r and reinstall a new one simple as that

Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install

I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

find the part (image is really helpful), buy, and replace. Like I said, it's really easy.

I unplugged the power to the stove first,
I removed the racks and cover plate at the bottom on the oven. Located the 2 screws holding the element igniter in place. I pulled the stove forward and removed the back cover plate and unplugged the old element.
Installed the new element and tested the igniter, special note my oven would not ignite the propane with the cover plate not first being installed. The igniter glowed but would not ignite fuel.

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great