CER1100AAH Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Derry, NH
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element
I shut off the breaker in the fuse panel for the range ( recommended)
I had to unscrew the two mounting plates, unclipped two wire connectors.
Reconnected the two wire connectors ( pull off, push on)
Done
Flipped on breaker and was baking in less than 15 minutes.
I had to unscrew the two mounting plates, unclipped two wire connectors.
Reconnected the two wire connectors ( pull off, push on)
Done
Flipped on breaker and was baking in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from donna, TX
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip bowls very dirty and stained
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Portland, OR
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner pan warped.burner sat at 15 degree angle.
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Searsport, ME
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heater Element Faile
Easily removed the oven and had access to the rear in under a minute undid the 2 Phillips screws retaining the element and replaced with the new element I had ordered it was just so simple!
Thank you as you saved us calling out an expensive technician avoiding unreasonable time and costs expenditure
Thank you as you saved us calling out an expensive technician avoiding unreasonable time and costs expenditure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Marshall, NC
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Juice from baking roast caused the element to break
unscrewed element from oven, traded wire connections to new element, screwed new element in - saved myself a $75 service call
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from Oskaloosa, KS
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Ham Lake, MN
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower Baking Element Broke
I removed the two screws that held the element bracket in place. I then pulled the element out a few inches and disconnected the wires. I then reconnected the wires to the new baking element, pushed the wires back inside the oven and resecured the bracket. NOTE: turn off the power to the oven! I thought that since the oven was not on, I could safely perform this replacement...unfortunately I got zapped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christi from Enid, OK
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom burner quit working
we removed the back I had my dad help me so he removed the wires while I removed the screws on the inside. When I received the part he also helped me replace it by putting on the wires while I put the screws in. Remember to disconnect from electricity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Coldwater, MI
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bake element broke in half and wouldn't heat
First I fliped the curcuit breaker to eleminate power to the stove. Then removed the 2 screws that hold the element in place. Then carefully pull the element out and disconnect. Installed new element to connectors and gently pushed back into the stove housing. Secured with the removed screws and turned back on the curcuit breaker. Turned on the oven and it worked like a charm..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cinti, OH
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was not getting hot
repair was easy- turned off power at electrical box, emptied out the wire shelves in the oven. Unscrewed two fasteners holding element in place, pulled element out about 3 inches, unplugged electrical end connectors.
Then got new part, attached two electrical connectors, slid back in place, fastened with two screws, turned power on and we're baking. I believe this part would be covered under my warranty- but we were having a party that weekend and I could not wait for the repair guy to do this on his schedule, plus his labor alone would have cost much more than my part and next day delivery.
Then got new part, attached two electrical connectors, slid back in place, fastened with two screws, turned power on and we're baking. I believe this part would be covered under my warranty- but we were having a party that weekend and I could not wait for the repair guy to do this on his schedule, plus his labor alone would have cost much more than my part and next day delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brittney from snellville, GA
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My baking element broke. Over wouldnt heat.
I ordered the part and it came in within 2 days from fedex! Great timing. It took me all of 10 minutes to fix the coil at the bottom of the oven. Fixed the problem and had plenty of time to cook dinner before my husband came home!!
GREAT SERVICE AT THIS SITE! They knew the right part! And the instructions are very simple.
Thank you
GREAT SERVICE AT THIS SITE! They knew the right part! And the instructions are very simple.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerard from Northport, NY
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned oit
Shut off the power to the stove. Remove the two screws retaining coil
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEFFREY from SUGAR GROVE, VA
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element Was Burned Out.
Very easy, with only the removal of 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Menominee, MI
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old bake element burned up
First I shut off the oven breaker, then I removed the racks and the oven door. I next removed the two retaining screws holding the element in place. I gently pulled the element forward to expose the blade connection. I disconnected the old element, attached the new element, slid it back into place and replaced the retaining screws. I remounted the door and turned the power back on. I did a test run on the oven. It worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glen from stamford, CT
- Parts Used:
- WPW10196405, W10196406RW, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drip bowls rusted i replaced them
remove elements and replace bowles
Was this instruction helpful to you?
Thank you for voting!