31203KAW Magic Chef Range - Instructions

Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Overall, it was painless and easy with zero problems

Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.

First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out back first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!

I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!

If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!

replaced the igniter in oven

I noticed that the ignitor would glow but the stove wouldn't light - I got the model number of the stove and googled the maytag model number. Came upon your website and realized that 94% of the time the problem was the amps were not enough to light the stove. I looked at all of the stories on how easy it was to fix. I ordered the part and received it within 3 days. I opened the door part way and lifted it straight up to remove it. I pulled out the bottom broiler plate by grabbing the back on pulling up. I undscrewed the wing nut of the flame bar and had easy access to the igniter. I removed the two nuts from the old igniter. Unplugged the igniter from the easy access door from the back and plugged in the new igniter. Replaced the access door and attached the igniter with the two nuts. Put the flame bar back on, put the broiler plate back on, put the door back on, plugged in the stove turned it on and success. It was so easy. I know in our area I would have paid near $200 for a service technician to come out and do what I did in approx. 20 Minutes and $50 for the part. Thank you so much for you website to help us not so talented appliance repair homeowners.

Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, you will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.

I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.

To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.