6892XVB Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donny from HASLET, TX
- Parts Used:
- WP74001870
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
oven not heating for baking
Had checked the continuity of the baking element, was good.
Had checked the volts or was it amps of the temp sensor, was good.
That leaves the relay board.
Cut the breaker off, pop open the front of the burner lid, braced it with a wooden spoon.
Used needle nose pliers to compress 3 plastic mounting connections.
Held new board inside and replaced each connection one at a time to from the old to the new.
Press back into place, lower and snap on stove top, hit the breaker and there ya go. Fixed. Everything works again.
Had checked the volts or was it amps of the temp sensor, was good.
That leaves the relay board.
Cut the breaker off, pop open the front of the burner lid, braced it with a wooden spoon.
Used needle nose pliers to compress 3 plastic mounting connections.
Held new board inside and replaced each connection one at a time to from the old to the new.
Press back into place, lower and snap on stove top, hit the breaker and there ya go. Fixed. Everything works again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LEXINGTON, MA
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The bake oven element burned out
Removed two screws and disconnected the element. Reconnected the new element and reinstalled the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Tomahawk, WI
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Bake element burned out
Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.
Don Samuelson
Don Samuelson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Littleton, CO
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The bake element burst.
Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Clarence, NY
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake Element shorted out
I first shut off the breaker to the stove - safety first!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leticia from Sunnyvale, CA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bakeing element caught fire.
First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new element, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Allyn, WA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned in half
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from ROCHESTER, IN
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element had burnt in half.
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from PATERSON, NJ
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element didn't heat at all
Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Warwick, RI
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element broke
****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into the holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulo from Cambridge Springs, PA
- Parts Used:
- WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our original surface element caught fire!
Old surface element was removed simply by pulling it out of the electrical contacts. The, the new one was inserted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from ROCKTON, IL
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace the lower oven element
Unplug the 220 cord..remove rear metal back ( 7-8 Ph/screws)... disconnect the red & yellow connectors from the back of the lower element. Remove-the-lift-off Oven door. Remove the two Ph/screws (one on either end of the element) At the very rear of the oven. Install the new element and reverse the about to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from WASHINGTON, DC
- Parts Used:
- 74003320
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Inner most oven door was broken.
I followed peoples instructions here, and it was not very difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Fredericksburg, VA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven baking coil had burned out
Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CONCORD, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Burner plugs were loose
used the supplied parts...very easy. The parts were exact replacements.
Was this instruction helpful to you?
Thank you for voting!