34MA-5TKVW-EV Magic Chef Range - Instructions

Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.

Unplugged two connectors and plugged into new burner. Couldn't have been easier! Also, I was so pleased that it matched the other three burners exactly!

Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.

Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.

My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.

Overall, it was painless and easy with zero problems

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!

I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....

Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.

Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.

Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.

Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.

To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!