6157WUA Magic Chef Range - Instructions

Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perhaps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!

Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.

First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.

Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.

Replaced the oven ignitor. Toughest part was removing old screws.

Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.

i removed old part, then installed new one. easy

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and 7. re-assemble steps 3,2,1. Easy

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

snaped them into oven cavity attached temp bulb job complete

Screwed in light bulb and glass protector

very easy