C3523WVA Magic Chef Range - Instructions

Unplugged the range. Took our the oven shelves. Unscrewed the bars holding the broken bake element to the back of the oven wall. Gently pulled out the wiring to which the bake element is attached. Slipped the ends of the broken bake element off the ending on the wiring. Then slipped the ends of the new bake element over the ends on the wiring. Then pushed the wiring with attached bake element back into their position behind the oven wall and attached the bars holding the bake element to the back of the oven wall. This is really easy because it is exactly like the on-line video, for I am a 75 year old female with little technical experience.

Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

used the supplied parts...very easy. The parts were exact replacements.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

first I removed the 2 screws, I then pulled the element out., accidently lost one of the wire in the insulation and had to take the back panel off which was 8 screws. Probably doubled my time. I received my part in 4 days thanks to good service and FedX It arrived the day before Thanksgiving. Just in time, Thank You All.

I Unscrewed the attachment plates located at the back of the over. Pulled the element out so that I could "unhook" the prongs. Replaced the new element by clipping on the prong attachement (you will see where the electrical wires are). Screwed the plates back on and Vola! I'm baking again.

Removed old element, pluged in new element.

First I removed the two screws that hold the element in place. I then pulled the element out about three inches and disconnected the two wires, being careful not to pull the plugs off. I then inserted the new element and reattached holders. It was very easy and took less than five minutes. The part arrived amazingly quickly. The stove works great now.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Rehooked up wires on new element, Slid the element in place. Replaced the two screws. Done, very easy.

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

My wife detected the problem Wednesday evening before Thanksgiving. We've had the heating element break before, so we knew right away what the problem was. We ordered the part that night, and even though we weren't able to cook Tom for Thanksgiving, the part shipped on Friday and arrived the next Thursday.

First, I turned off the power to the stove at the circuit breaker.

Then, I removed the two screws that hold the element in place. They are on the top of the flange and partially concealed by the convection element that juts out.

I pulled out the heating element, disconnected the electrical leads, and installed the new one.

I attempted to put the screws back in, but they were a little tough to line up. I decided to leave them out, knowing that I will probably be doing this repair again in a couple of years.

Hopefully, next time it won't be the day before Thanksgiving.

My husband removed the screws holding the damaged element and removed it before the new one arrived. When we received the replacement part, it took only about 10 minutes for him to repair the oven, inserting the new element.

Turned off power circuit to oven. Removed old element by unscrewing two nuts attaching unit to back of oven. Used pliers to help release electrical connections at both ends of element. Re-attached connections to new unit. Screwed nuts back into place. Turned power back on and cooked dinner. Total time for repair was less than 5 minutes.