38FN-4CXW Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from Hampton, VA
- Parts Used:
- WP7711P466-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing clock knob
placed knob on clock shaft with my fingers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Atlanta, GA
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aurelio from Lebanon, NJ
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Bad broil grill
Once oven was removed from wall not to bad
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NORMAN W from Waleska, GA
- Parts Used:
- 7201P036-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gasket was leaking heat from oven
removed old and installed new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Schertz, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremie from Freeland, WA
- Parts Used:
- WPY04000041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Easy installation
Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max from Bothell, WA
- Parts Used:
- WPY04000041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat up properly to set temperature
The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.
Was this instruction helpful to you?
Thank you for voting!