3121XRA-UX Magic Chef Range - Instructions

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

The Just Answer website answer felt certain that the igniter was the problem, and hence I ordered a new igniter.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.

We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a brand new oven!

remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.

Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.

Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.

very easy

Screwed in light bulb and glass protector

This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is held on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.

After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.

Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.

First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.