35JA-13XS-MS Magic Chef Range - Instructions

Very simple, unscrew the old element. Remove the electrical spade connectors and reverse to install new element. The folks at parts select.com were very helpful and even after I ordered the wrong part, the return process was hassle free. Prompt shipping, very happy.

ordered new broiler pan

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Turned off power, first then removed two screws
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.

snaped them into oven cavity attached temp bulb job complete

Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Once oven was removed from wall not to bad

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

The Burner Control Switch - 250V Part Number: PS2089409 that this site recommended was the right part for this older range. Had to remove screws to pull out the front panel with knobs, but it only pulls out a couple inches due to wires so it is tight to remove old switch. The five tabs are not in same spot so go by the labels and the wire lugs fit just fine, and the knob snapped right on and works great. Thank You!

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.