CGR3740ADW Magic Chef Range - Instructions

1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3

The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...

slide latches in rear of floor panel forward and remove.

Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.

I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the old ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!

took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like new .

removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine

Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.

This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!

I got on-line, found your website, put in the required information (model #, brand, part, etc.) and ordered. Before ordering however, I measured, looked at the picture on-line, and compared to the part I needed. It looked right. I ordered, and the parts came in a timely manner. Got an e-mail saying they were ordered, then another e-mail saying they were shipped. Got the parts, installed, they look so good. I'm very pleased. Thanks!

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.

Replaced the water valve. I knew that the ice maker was working by watching the movement. It was not getting water to it, s I figured it was the electric water valve and sure enough, that fixed the problem.