34FA-92CKXW Magic Chef Range - Instructions

I was afraid I would have to remove the built in oven from the wall to do the repair but it was simple. I pulled on the wire a bit and the connector popped out of the hole in the back. After that it was as simple as removing 2 screws, replacing the unit, plugging it in and pushing the new connection out the hole in the back. They included a piece of insulation with the kit that I then forced into the hole to protect the new plug from the heat of the oven.

Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.

I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.

Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of seconds!!

Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.

was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!

the igniter would glow but the gas would not flow...
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.

Un-did the old one put in the new. Iam 63 years old and a woman. Repair men wanted 500.00 plus to come out and repair I did it for cost of igniter in 15 min. Oven works great! Thanks parts select for making it so easy!

2 screws easy to remove and plug in the wire. job done.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.

Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.

Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was harder than this.

i removed old part, then installed new one. easy

I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.

I looked online and ordered the part. It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.

I baked several batches of Christmas cookies and three coffee cakes the next day.

Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.