3889VRV-Z Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from Troy, AL
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
F2 and F5 if I remember correct.
Removed the two screws pulled the element out and unhooked the wires then used one of the included adapters to reinstall the new sensor then screwed the two screws back in to secure the sensor. Everything works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Newport News, VA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn gasket
Removed old gasket and replaced with new gasket'
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Dover, DE
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Damaged the oven lamp socket while removing a broken bulb.
Upon receiving the replacement part, I noted that the socket was held in place by simple expanding tabs. TURN OFF POWER TO THE OVEN. Using a right angle pick or similar tool, bend the tabs inward on the existing socket and remove. Disconnect the white, black and green wires. Note which tab is the green tab. Attach the wires to the new socket. Push the new socket into place, aligning the key bump on the socket with he slot in the oven wall opening. Install bulb and diffuser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- boonsom from inglewood, CA
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven goes off like unplug no light no heat panel light come back on when oven get colder
the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lancaster, NY
- Parts Used:
- 12400043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken oven door hinge
Oven is built in. The only way to access the hinges is to pull the oven out and remove the sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Louisville, KY
- Parts Used:
- W10823704
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hotplate not working
Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilma from Ranger, TX
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
flashing f1 and f3 and then would go off, oven would not come on
Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Metairie, LA
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heat sensor went out causing oven to shut down.
Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from West Allis, WI
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The top oven of the two oven stove would not heat past 105 degrees.
First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was very easy just as the video showed. Stove was repaired in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RANDALL from Washington, IL
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After the oven reached desired setting and turns off, the oven wouldn't relight.
I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.
Was this instruction helpful to you?
Thank you for voting!