31HA-10KXS-ON Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Petaluma, CA
- Parts Used:
- WP7501P133-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Oven would not lite
With a little adjustment to the mount the part went in ok. Checked the oven works like new; well better than new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Treasure from High Point, NC
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't ignite
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from Downey, CA
- Parts Used:
- WP7711P135-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the burner knobs broke off
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Caliente, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Oven wouldn't ignite
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caroline from South Windsor, CT
- Parts Used:
- 3412A004-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
30 year old gas stove needed a new burner assembly.
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathreen from Lusby, MD
- Parts Used:
- 12400034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no temp control
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr. J.C. from Haines City, FL
- Parts Used:
- 3412A004-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gas manifold had holes in it.
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roman from West Caldwell, NJ
- Parts Used:
- WP7403P190-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Igniter Switch on the burner was constantly on
To get to the switch I had to remove the knobs and the front panel of the burner valves. There were some dozen screws, top and bottom holding the panel in-place.
The switch slid off the burner valve stem easily but removing the wires I had to pull with the pliers. There seamed not to be a wire release that I could see.
Replacing the wires was no problem. They slid into place by just pushing them in. Assembly was the reverse.
The switch slid off the burner valve stem easily but removing the wires I had to pull with the pliers. There seamed not to be a wire release that I could see.
Replacing the wires was no problem. They slid into place by just pushing them in. Assembly was the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAY from BRIDGEPORT, CT
- Parts Used:
- WP7711P135-60, 3412A004-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A high flame was coming out of the side of the burner
Easy......pulled out the old one easily and popped in the new one.......saved a lot of money...no repair bill for either diagnostic fee or assembly fee ...No mark up for the part either. Very happy mom!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Wisconsin Rapids, WI
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The oven igniter lit up but the valve wouldn't release the gas to ignite.
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Secaucus, NJ
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven would not turn on flame
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from marine city, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven wouldn't light
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from FORT WORTH, TX
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Self tapping screws stripped out, one broke in mounting hole
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from PORTERVILLE, CA
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Oven ignighter no longer works
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel tool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!
Barry
Barry
Was this instruction helpful to you?
Thank you for voting!