CGR1110ADW Magic Chef Range - Instructions

Replaced gas oven ignitor

Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.

i ordered the part, it came in speedy quick,and it was very easy to install i saved $200 bucks, and my mom was the happiest person in the world. thank you.

First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.

1. Turn off the gas (propane)
2. Unplug the oven.
3. disconnect the gas line and pull the oven out.
4. remove the back panel to access the igniter.
5 disconnect the igniter.
6. unscrew igniter/gas assembly and remove from oven (two screws).
7. unscrew igniter (two screws)
8. replace igniter with new.
9. reassemble in reverse order.
10. turn on stove.
11. Happy wife, happy life.

I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!

First I tried oven ignitor. Did not cure the problem. Then ordered short sensor and it cured the problem. Pull range out & unplug unit.From inside unit remove two screws holding short sensor in &pull out from inside. Unhook sensor. Slide in new sensor& secure with two screws. Had to remove two screws on back of oven to plug in sensor to existing plug. Very simple job.

We ordered the replacement igniter and basically was very easy to replace. We ended up spending $50 for the part as opposed to spending $261.00 that Sears was going to charge.

Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great

I started with pulling the base of the oven to examine the mechanism underneath. The hardest part of the whole thing was working the wire connection past the metal back of the oven. It required prying the metal away from the frame rail and wedging the wire connection through. Other than that it was unplugging the old, plugging in the new, and a few screws to reattach the igniter, heat sheilds, and oven base.

followed instructions from repair manual.

The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.

seamed easy enough. Found the part and it looked identical, However I could not see the connector in the picture because the logo covered that part of the picture. Had to cut the connector off the old igniter and crimp it on to the new ingniter.

It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!