55HN-1W Magic Chef Range - Instructions

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

new drip bowl fit perfectly and was a snap to install.

Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

New receptacle element. I am a girl and I did it.!!!!

Pulled the range away from the wall and took out all the screws of the back panel. I had two different screws. Removed the dial and took two screws out behind the dial. Carefully removed the wires and placed them on the new switch. Screwed switch to panel, replaced dial and put the back panel back on range. Pushed range back into place.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!

Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number switches.

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

This worked out GREAT. We were about to purchase a new range when I found the needed parts were available. The stores we had contacted had told us our range was too old to have parts available. I had no problem with installing the receptacle at all. The pans went in easly as excepted. My wife is happy with her NEW arrangement. She does not need to learn how to operate a new range. Thanks for your help. The instructions sent were clear and easy to follow.

1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.