6898VRA Magic Chef Range - Instructions

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

Unplugged the stove. I removed the old element by removing the two screws holding it in, and plugged the stove back in. I ordered the part and it came in 2 days. Unpluged the stove again, connected the new element, and re-attached it via the two screws. Plugged it back in, and it worked great. Fantastic price and quick delivery. Only took about 5 minutes to fix, and I saved at least $100 by not having to call a service man.

Remove 2 screws and replce element (turn power off first). Pull old touch panel off and unplug. Plug in new touch panel and stick to front off appliance.

Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.

I didn't. Don't know how to get to light bulb to change it for this specific model

It was really easy. It took about 5 minutes to remove the screws holding the back in place. Another couple of minutes to remove the switch, and a few more minutes to change the wires over one at a time. Then 5 more minutes to put it all back together again, and plug it back in, and it just worked. Really simple.

Removed 4 screws holding top cover in place.
Took out knobs.
Removed side slides holding panel glass in place
Unplugged Touch panel from ECU
Pulled off old touch panel.
Used WD-40 to remove old adhesive from panel glass
Had to enlarge timer knob hole on new touch panel to fit old knob
Installed new touch panel and plugged back in
Cleaned old greasy areas that were not touched in years (anal retentive action)
Re assembled everything else

6 days and no F1 error or beeping

Very fast shipping from PartSelect.com

Thank You

Turn off power ,pull off clock and timer buttom ,lift the light cover , remove a screw on each side of the light, ,than with the stuby screwdriver remove one screw on each side at bottom of front glass, front glass should come loose. peel off the control plate .it is just stuck on the glass front. you will then see where the wire plug go's , unplug the old discard the entire front panel you just peeled of ,,feed new panel wire through the hole and replug it . it only go's one way,peal and stick the control panel., put glass front back ,replace the screws,

Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brackets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

Slide smooth stove top back. then removed 2 screws on top and 2 on bottom of clock and control mechanism. disconnected the touch pad and peeled it of f front of stove. Cleaning the adhesive from under the touch pad took the longest. I did that with rubbing alcohol. I then peeled the backing off the new pad and put it in place. Reconnected the clock and control mechanism and replaced the screws. No more alarms.
When I had called Whirlpool (the now makers of Magic Chef). They told me I would have to have a technician diagnosis the problem and if what I thought was wrong, the part was no longer available. The technician had told me if they could get the part it would cost $289-$389 to replace. Thanks to Partselect and everyone here it cost me $100 and I had the part the next morning.

i removed the two screws that holds the element in. I pulled the element out and disconnected the wires and I had to adapt a double male adapter to the wire ends and plug the wires back onto the element. The old element had male spades and the new element had female spades.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.