CGR1420BDW Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Reno, NV
- Parts Used:
- 74003387
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old bulb fused into old socket.
removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Hardy, AR
- Parts Used:
- 74006281
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven would not maintain set temperature.
1. Closed gas valve at stove supply outlet.
2. Unplugged stove electrical connection
3. Unplugged electrical connections to defective valve
4. Removed 4 screws on burner side of heat heat shield
5. Disconnected gas inlet to defective valve
6. Removed 2 screws holding valve retainer to bottom of unit
7. Lifted gas burner inlet tube while pushing valve toward rear of unit - - - (a bit tricky)
8. Removed valve from rear by tilting forward so valve outlet clear the burner inlet tube and heat shield. Heat shield is not removed, but must be raised enough to allow passage of the valve outlet protrusion.
9. Installed new valve by repeating the preceding steps in reverse.
10. Reconnected gas and electrical, and checked performance
2. Unplugged stove electrical connection
3. Unplugged electrical connections to defective valve
4. Removed 4 screws on burner side of heat heat shield
5. Disconnected gas inlet to defective valve
6. Removed 2 screws holding valve retainer to bottom of unit
7. Lifted gas burner inlet tube while pushing valve toward rear of unit - - - (a bit tricky)
8. Removed valve from rear by tilting forward so valve outlet clear the burner inlet tube and heat shield. Heat shield is not removed, but must be raised enough to allow passage of the valve outlet protrusion.
9. Installed new valve by repeating the preceding steps in reverse.
10. Reconnected gas and electrical, and checked performance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CHESTER, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
replace igniters
Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from BUDA, TX
- Parts Used:
- 74007498
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
My igniter burnt out. My oven stopped lighting up.
I ordered a new igniter and when it arrived, i removed the door from the oven. It just lift's off. I had to removed two screws from the bottom plate to gain access to the igniter. Remove the two screws from the igniter and unplug it from the back of the lower back of the stove. Place the new igniter where the old one was and plug it in. Put new screws in and tighten them down. Put the bottom plate back in its place with screws tightened. Put oven door back on and turn on the oven. That's all there is to it. Your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from LYNDEN, WA
- Parts Used:
- 74007498
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No problem
Very easy install. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Monroe, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
floor panel heavily stained and warped
slide latches in rear of floor panel forward and remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from WINCHESTER, MA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Can Francisco, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
corroded burners
Unscrew the burners an install new ones! Anyone could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramiro from Bernalillo, NM
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Replaced burner
Went well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- javier from Santa Ana, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bad Gasket
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Staten Island, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner was eroded on the bottom and flame was coming from undernealth the burner
Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from CLARKS SUMMIT, PA
- Parts Used:
- 74007498
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Faulty oven igniter
Removed door and bottom oven pan to expose igniter. It was held in place by two sheet metal screws. Tried to back them out but due to heat damage , they stripped. I used my versa tool with a metal blade to cut the screws. I removed the old igniter and disconnected the plug, after I guided it out from the insulation. I installed the new igniter with two new self tapping screws after I connected the plug and guided it back through the insulation. Reinstalled the oven pan and door. I set the oven to 350° and the new igniter worked. Wife is happy and I saved the repairman fees.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fresno, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not maintain temperature
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.
Was this instruction helpful to you?
Thank you for voting!