3167VUV Magic Chef Range - Instructions

New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.

I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. After removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.

Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.

The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...

It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!

I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.

I got on-line, found your website, put in the required information (model #, brand, part, etc.) and ordered. Before ordering however, I measured, looked at the picture on-line, and compared to the part I needed. It looked right. I ordered, and the parts came in a timely manner. Got an e-mail saying they were ordered, then another e-mail saying they were shipped. Got the parts, installed, they look so good. I'm very pleased. Thanks!

I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .

I took the broiler pan out of the shipping container and put it in the oven.

Went well

Unscrew the burners an install new ones! Anyone could do this.

Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.

Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.

part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.

ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.