38JN-2CW Magic Chef Range - Instructions

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.

Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.

Put in the new drip pan -- which are really nice shiny ones.

Just remove old bowls from range top and put new ones. That is all ... just super simple! :)

Remove old drip bowl from the range and put a new one back.

We just installed the new rack in the oven. The amazing thing (after many unsuccessful attempts to find the correct rack) was having a friend recommend partselect.com. The gentleman I spoke to was extremely knowledgeable, helpful and efficient. We had our new rack 2 days after placing the order. We thought that kind of service didn't exist any more! Thank you so much. Now we can make 2 pizzas at the same time!!!

I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.