3488VVS-N Magic Chef Range - Instructions

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).

I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concise diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.

The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.

I used a pipe wrench to turn the old burner off and removed the crumbling washer underneath- no need to replace this. I took off the 2 wires, crimped them onto the new burner, twisted it back into place and presto- all fixed!

The repair was a no brainer - twist to release the old burner - disconnect the spark wires. connect the spark wires on the new unit - drop it in and twist to lock - about 2 minute job

replaced heat sensor

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.

New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.

ordered new replacement oven igniter kit and also felt it was a good opportunity to change the oven temperature sensor so also ordered short oven sensor kit. both parts fit as described as original replacements with very little work involved. oven worked properly good well done and a big saving on a service call repair or new range.

using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.

I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. After removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.