35JA-13XS-ON Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Lodi, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Burner element stopped working
The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elroy from Atwater, MN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner not operating or intermittently
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Florissant, MO
- Parts Used:
- WPY04000041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The original bake element burned out
1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Hodgen, OK
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner stayed on "high", could not adjust heat
I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Oak Lawn, IL
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner was in full hot.
Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darwin from wisconsin rapids, WI
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Framingham, MA
- Parts Used:
- 7801P030-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Somehow one of our oven racks was missing - maybe taken inadvertently from beside old refrigerator when it was removed.
We just installed the new rack in the oven. The amazing thing (after many unsuccessful attempts to find the correct rack) was having a friend recommend partselect.com. The gentleman I spoke to was extremely knowledgeable, helpful and efficient. We had our new rack 2 days after placing the order. We thought that kind of service didn't exist any more! Thank you so much. Now we can make 2 pizzas at the same time!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martien from williamstown, MA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
one pole of the socket corroded to nothing
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!