3100SPW-K Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Friend, NE
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Seal on oven was old, hard and breaking apart.
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Treasure from High Point, NC
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't ignite
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Fresno, CA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Seal was fallinig off
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Caliente, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Oven wouldn't ignite
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Colton, CA
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven floor panel was warped.
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from Downey, CA
- Parts Used:
- WP7711P135-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the burner knobs broke off
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from South Beloit, IL
- Parts Used:
- 7501P137-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Over wouldn't light.
Saw that the igniter came on, but no gas flow.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANDREA from CORNING, CA
- Parts Used:
- WP74002419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had To Change The Knob I Could Not Read It
Pulled the old knob off and put the new one on. Only thing that was difficult was making sure the knob was the right one because the instructions kept leading me back to a different brand of appliance but since the photo looked alike I went ahead and got it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caroline from South Windsor, CT
- Parts Used:
- 3412A004-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
30 year old gas stove needed a new burner assembly.
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Schuylkill Haven, PA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bad Door Gasket.
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Prosperity, SC
- Parts Used:
- WP7711P135-60, WP74002419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Original Knobs broken; would not work
Removed the aftermarket knobs I originally bought (they would slip or not turn at all) and installed the new Magic Chef knobs on stove. They work perfect! No problems, easy to install and work every time. Thank you so much for your quick shipment. It is now fun again to be cooking, and not worrying about whether the knobs will turn or not. Thank you, thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr. J.C. from Haines City, FL
- Parts Used:
- 3412A004-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gas manifold had holes in it.
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Washougal, WA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Stove seal fell apart
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Wisconsin Rapids, WI
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The oven igniter lit up but the valve wouldn't release the gas to ignite.
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Secaucus, NJ
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven would not turn on flame
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!