CER1125ACW Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- tommy from FAYETTEVILLE, NC
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No problem installing the sensor
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James H from Victor,, NY
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken Coil
Very easy to install with the advanced instructions you provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from CAMAS, WA
- Parts Used:
- WP74010750
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
None at all.
Just took the old one out and put the new one in. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Arvada, CO
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not hold temperature, not turn on, and would shut off during use.
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from MONTICELLO, UT
- Parts Used:
- WP9761346
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Stove burner burned out
Very helpful customer service Lady.
Helped me select the corect burner replacement.
And helped me get it ordered.
Repair went very well.
I recomend Parts Select if you need parts for.
Helped me select the corect burner replacement.
And helped me get it ordered.
Repair went very well.
I recomend Parts Select if you need parts for.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Nashville, TN
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven door was locked, couldn't set oven temps
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from ELKTON, VA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from GUSTON, KY
- Parts Used:
- WP74010750
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element in oven went out
Take out 2 screws. Unplug the old element, plug in the new one and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mz from COLUMBIA, ME
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from TROY, MI
- Parts Used:
- WPW10310249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The broiler broke at the ends.
My daughter repaired it without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Winter Haven, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot
After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from Oskaloosa, KS
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Ham Lake, MN
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower Baking Element Broke
I removed the two screws that held the element bracket in place. I then pulled the element out a few inches and disconnected the wires. I then reconnected the wires to the new baking element, pushed the wires back inside the oven and resecured the bracket. NOTE: turn off the power to the oven! I thought that since the oven was not on, I could safely perform this replacement...unfortunately I got zapped.
Was this instruction helpful to you?
Thank you for voting!