CGR3760BDW Magic Chef Range - Instructions

I used a pipe wrench to turn the old burner off and removed the crumbling washer underneath- no need to replace this. I took off the 2 wires, crimped them onto the new burner, twisted it back into place and presto- all fixed!

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

replaced heat sensor

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

The gas supply lines are included with the Assembly. The only tools needed to remove the old and install the new assembly were a phillips screwdriver and an small adjustable wrench. NOTE: The burners can be removed from the range top by carefully turning the burner to the right no need to lift the range top (I used a pipe wrench and very light pressure). $50 repair turned into $150 repair

1. Remove the oven door by opening a few inches and lifting straight up. Remove racks to access it. 2. The old igniter is just held in by two nuts that have a screw head in the middle of them so they could be removed by a nut driver or by a screwdriver. Unfortunately, both of our screws threads were terribly stripped and after first trying to use pliers to help remove them, we ended up using a dremel tool to cut them off. 3. unplug the old igniter and take it out. 4. Plug in the new igniter. 5. attach the two screws. (our time on the repair was mostly spent trying to find two screws around our house that would replace the two that were stripped--otherwise this would have been 15 minutes). 6. return the door and racks by the sliding the door downwards onto the hinges

Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.

Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

Very easy install. Works great.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

slide latches in rear of floor panel forward and remove.