3187VTV Magic Chef Range - Instructions

1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.

First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven worked perfectly

The igniter was located in the bottom of the stove or broiler section. It was hard to get at, but with a little trial and error I figured out how to take the plate between the oven and broiler. Now the igniter was easily accessable. 2 screws on the igniter bracket, then simply unplug the electrical. The igniter supplied had the identical electrical plug (plug and play). The new igniter works like a charm-oven ignites in about 15 seconds. Piece of cake!!!!!

I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

replace burner-had to hit old burn with rubber mallet to break off grease and took old burner off-two wires were connected to it..put those on new burner and was done--have a little problem--flame is lower now than it was-but it turns on

took oven tray out and loosened igniter and replace same works great.

The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.

it was so easy my wife could do it!!!!!!!!

Unplug electric cord,turn off gas,replace parts,check for gas leaks.Done....

Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.