35JA-13LXS-ON Magic Chef Range - Instructions

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Very simple, unscrew the old element. Remove the electrical spade connectors and reverse to install new element. The folks at parts select.com were very helpful and even after I ordered the wrong part, the return process was hassle free. Prompt shipping, very happy.

ordered new broiler pan

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

Turned off power, first then removed two screws
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.

Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

snaped them into oven cavity attached temp bulb job complete

Once oven was removed from wall not to bad

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing