S34JK-4TKXW Magic Chef Range - Instructions

Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.

To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!

It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out back first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!

I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!

Removed burnt bulb. On replacing the bulb I glued the bracket, retainer gasket and bulb cover together- I used only a small amount of glue-just enough to hold the three items together. You need to do this since the three items slip in your hand while you attempt to screw the bracket to the oven wall. Need my help, email me @ Lexidog999@tx.rr.com

If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.

Furtunately, it was just a replacement of the drip pans. It changed the entite looks of my range for under $ 25.00 dollars. Very satisfied!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

Remove two screws back panel and remove sensor two screws inside top oven.

1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.