S34JK-4TKXW Magic Chef Range - Instructions

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.

Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.

Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.

First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by removing the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!

My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who added their comments! They gave us courage to give it a try.

We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!

I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !

remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.

To get to the switch I had to remove the knobs and the front panel of the burner valves. There were some dozen screws, top and bottom holding the panel in-place.
The switch slid off the burner valve stem easily but removing the wires I had to pull with the pliers. There seamed not to be a wire release that I could see.
Replacing the wires was no problem. They slid into place by just pushing them in. Assembly was the reverse.

Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.

moved stove away from the wall, Disconnected power, Removed 2 screws on the access panel and removed panel. Disconnected qwick release conections on heat sensor and ignitor, Removed oven door and burner cover to expose ignitor, removed 2 screws to remove ignitor and replaced ignitor. Removed 2 screws and removed sensor, replaced sensor. Reconnected qwick conects on sensor and ignitor. Replaced oven door, burner cover and access panel and checked out. Checks OK !

So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.