31HA-92KX-EL Magic Chef Range - Instructions

Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.

After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.

Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.

First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.

I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.

I looked online and ordered the part. It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.

I baked several batches of Christmas cookies and three coffee cakes the next day.

very easy

Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.

Rick,
Detroit, MI.

Replaced the oven ignitor. Toughest part was removing old screws.

I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.

Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.

Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the igniter came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.

My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.

Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

snaped them into oven cavity attached temp bulb job complete