586W-2C Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Erica from Ivyland borough, PA
- Parts Used:
- WP660532
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement of heating element for elec. stove
plugged it in to the spot where missing element was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John J from Coatesville, PA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Porcelan Electric Burner Plug broke
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Carnegie, PA
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty drip bowl
Remove old drip bowl from the range and put a new one back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Brookfield, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner failure
Removed and replaced burner unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judy from coarsegold, CA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner fell apart
Just plugged it in and away I went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elroy from Atwater, MN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner not operating or intermittently
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from south bend, IN
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
surface burner stopped working. Was not heating up.
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darwin from wisconsin rapids, WI
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Oak Lawn, IL
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner was in full hot.
Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from New Hope, PA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner stopped working. Replaced burner & block.
We read comments by other DIYers and then looked at the video on YouTube. Our range is old and the screw holding the clamp for the block was too tight to remove so we removed the block from the old clamp and left clamp intact. Turned the circuit breaker off. Cut the existing wires and wired the new block to them. Put the block back into the old clamp, put new surface burner in and good as new. My boyfriend and I did it together but I could have done it myself - it was that simple. Thanks PartSelect for quick delivery and excellent DIY info.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Hodgen, OK
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner stayed on "high", could not adjust heat
I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Oak Lawn, IL
- Parts Used:
- W11122006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner was always in high temperature.
Pulled the range away from the wall and took out all the screws of the back panel. I had two different screws. Removed the dial and took two screws out behind the dial. Carefully removed the wires and placed them on the new switch. Screwed switch to panel, replaced dial and put the back panel back on range. Pushed range back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Falls Village, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner stopped heating
Unplugged the old one and plugged in the new, which you sent promptly. No tools. Easiest fix ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Bangor, PA
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not heat
Took the old burner out and inserted the new one. The burner was received two days after ordering. I was very satisfied with the service.
Was this instruction helpful to you?
Thank you for voting!