3468VTV Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lloyd from Cocoa, FL
- Parts Used:
- 12001596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burners would not lite
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped. Thanks Lloyd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- june from wills point, TX
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glynne from Dedham, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Oven was not working at all
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pati from Marietta, GA
- Parts Used:
- WP74006427
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Oven wouldn't heat, broiler would.
Removed all screws from back panel of stove, disconnected all electrical, shut off gas. Removed valve and replaced with new. Put all back together. Turned on gas and checked for leaks. Success!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wesley from ODENVILLE, AL
- Parts Used:
- WP7407P182-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
original fixture required bulb - this fixture (all-in-one) was great
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONNIE from SAG HARBOR, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Igniter for oven not working
Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from West Winfield, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light reliably.
Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Missing gasket under burner caused gas to leak out
I followed the video and it was incredibly easy. I shut the breaker off (we live in an apartment, and pulling the plug on the stove wasn't possible). I lifter out the old burner (the gasket underneath was corroded, and I just threw it out, as the newer burners are self-sealing); removed both the igniter wire and the ground wire (I needed a pliers to tug the igniter wire off); attached the new burner; replaced the burner; turned on the power; and voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from WATSONVILLE, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
BURNER DID NOT IGNITE. HOLE ON SIDE OF BURNER HAD A HOLE, SO FLAME WAS UNEVEN.
USED CHANNELOCK PLIERS TO ROTATE BURNER COUNTER-CLOCKWISE. PULLED OFF THE CONNECTORS, APPLIED RUST TREATMENT TO THE REPLACEMENT PART, WHICH HAD ITSELF STARTED TO CORRODE. SPADE LUGS ON THE OLD PART HAD A SPADE ADAPTER, BUT THE CONNECTION SEEMED TO WORK REGARDLESS OF THE MISS-MATCH. PART WAS REPLACED, TURNING THE BURNER CLOCK-WISE. VERY QUICK AND EASY REPAIR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from CLARKS SUMMIT, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Oven would not ignite
Very easy, video helped tremendously
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Spotswood, NJ
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat up fully, smelled of gas.
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from DAYTON, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas would come on, would not ignite. Oven not heating.
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from CINCINNATI, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from AURORA, MN
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No heat in oven
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from ELMIRA, MI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Sealed burner was rusted out. Had a hole in it.
Unplugged two connectors and plugged into new burner. Couldn't have been easier! Also, I was so pleased that it matched the other three burners exactly!
Was this instruction helpful to you?
Thank you for voting!