35DN-2CX (CODE21) Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Thornton, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burned out, broke circle, heat only half
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra Collignon from SANTA CLAUS, IN
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from SEATTLE, WA
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Half of broiler element worked
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Hughes Springs, TX
- Parts Used:
- WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not heat.
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alex from huntington, NY
- Parts Used:
- WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace element
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Elba, AL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burnt out
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Portland, OR
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner pan warped.burner sat at 15 degree angle.
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cherie from Dowagiac, MI
- Parts Used:
- WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Large burner on stove not working
I removed the heating element and noticed that the prongs were corroded. I looked for a model number but couldn't find it so it made it difficult to find a replacement until I got on this website. I found the replacement part and also found that as I checked for other sites for this part this company was the most resonable priced.
The part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.
The part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary L from North Tonawanda, NY
- Parts Used:
- WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner ceramic disintegrated & spalled
Pulled buner element out of socket as you would for detailed cleaning. Replaced burner element & drip pan with OEM parts. Fit was perfect, tested burner on all heat ranges, good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter J from Boynton Beach, FL
- Parts Used:
- WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element broken
Very simple, unscrew the old element. Remove the electrical spade connectors and reverse to install new element. The folks at parts select.com were very helpful and even after I ordered the wrong part, the return process was hassle free. Prompt shipping, very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Star, ID
- Parts Used:
- WPW10196405, WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Element had burned out
Package arrived while I was working at the computer and my husband announced minutes later, "That's what I like to see". I didn't know what he was talking about until he tossed the packing list on my desk and said, "It works perfectly. Good Job!" It had only taken a minute to pop the new parts in and he already had water on for coffee.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tama from Pacific Grove, CA
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Simple - needed to replace the drip pans on the stove between tenants in a rental apartment
This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Traverse city, MI
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
element shorted out startedto arch inside oven
Turned off power, first then removed two screws
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from wellsboro, PA
- Parts Used:
- WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element burnout
The repair was just a matter of sliding the old one out and plugging the new one in. The ease of use of this website was wonderful. Super fast shipment. Im very pleased.
Was this instruction helpful to you?
Thank you for voting!