34DA-4CKXW (4X) Magic Chef Range - Instructions

Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!

open oven door remove bottom tray pull off two screws unplug wire remove old part install new part

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!

the igniter would glow but the gas would not flow...
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.

Un-did the old one put in the new. Iam 63 years old and a woman. Repair men wanted 500.00 plus to come out and repair I did it for cost of igniter in 15 min. Oven works great! Thanks parts select for making it so easy!

2 screws easy to remove and plug in the wire. job done.

The Just Answer website answer felt certain that the igniter was the problem, and hence I ordered a new igniter.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.

We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a brand new oven!

I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.

Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of seconds!!

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.

I looked online and ordered the part. It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.

I baked several batches of Christmas cookies and three coffee cakes the next day.

My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.

Replaced the oven ignitor. Toughest part was removing old screws.

I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.